Are all toilets a standard size?

The standard distance is 12 inches, but 10 or 14 inches are occasionally found in older homes. Determine the rough-in in your bathroom by measuring from the wall behind the toilet to the middle of the bolts on the base, and compare to your desired toilet’s dimensions.

Likewise, people ask, is round or elongated toilet better?

Most people find elongated toilet bowls to be more comfortable, but in a small bathroom, a round bowl can save space. Elongated toilet bowls measure up to 31″ from the wall, while round fixtures max out at 28″. Because round bowls are less expensive than elongated bowls, they save a few dollars, too.

Is my toilet bowl round or elongated?

it’s a noticeable difference. If you’re still wondering, you can measure from the two mounting bolts at the seat hinge to the very front of the toilet bowl. That measurement will be about 16 1/2 inches if the bowl is round, and 18 1/2 inches if your bowl is elongated.

How do you measure for a new toilet?

To find out your toilet’s rough-in, measure from the wall behind the toilet to the middle of the closet bolts, which hold your toilet to the floor. That distance will likely be a bit more than the standard 10″, 12″, or 14″ rough-in dimensions. Round your measurement down to the nearest standard rough-in.

Are toilet seats a standard size?

For your reference, the standard measurement for US toilet seat bolts is 5.5 inches. Measure the width of the bowl at its widest point. If you have a round bowl, this dimension should be about 16.5 inches. If you have an elongated bowl, the measurement should be around 18 to 18.5 inches.

What is the size of a standard toilet?

The depth can be as little as 14 inches (35 centimeters) and as much as 20 inches (50 centimeters). Toilets. You need at least 30 inches (76 centimeters) of clear width for toilets, but 32 to 36 inches (81 to 91 centimeters) is much better for most people.

What is the standard size of a toilet?

Total height of one piece gravity toilet might vary from 21 to 30 3/4 inches (53 – 78 centimeters) with 14” – 16” (356 – 406 mm.) distance from the floor to bowl rim. Depth usually stays within 27” – 30” (686 – 762 mm) and width very rarely exceed 20 in (508 mm).

What is the size of a standard toilet seat?

If you prefer to measure, just to be sure, then measure from the front of the bowl to the middle of the screws at the back of the bowl/lid area. Here are the standard toilet bowl sizes: Round Toilet Bowl: 16.5 inches. Oblong Toilet Bowl: 18.5 inches.

Which toilet has the best flush?

Best Flushing Toilet 2018: Editor’s Top Pick

  • WoodBridge T-0001, Dual Flush Elongated One Piece Toilet.
  • KOHLER 3810-0 Santa Rosa Comfort Height Elongated 1.28 GPF Toilet.
  • Dometic 320 Series Standard Height Toilet w/Hand Spray, Bone.
  • TOTO MS604114CEFG#01 Ultramax II Het Double Cyclone Elongated One Piece Toilet.
  • How much room do you have to have around a toilet?

    Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.

    How far does a toilet have to be away from a wall?

    Standard drywall is 1/2 inch thick, so the plumber should set the toilet flange at least 15-1/2 inches from the center of the flange to the wall framing. The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing.

    What is the dual flush toilet?

    A dual-flush toilet is a variation of the flush toilet that uses two buttons or handles to flush different amounts of water. Although the first generation dual-flush toilet caught on, a redesign in 1993 cut water usage in half compared with traditional toilets, when used properly.

    How much does it cost to install a new toilet?

    A standard toilet install should take between one and two hours to complete and cost an average of $348 or less. Basic installs will run around $115. Unexpected costs could raise the cost up to as much as $800.

    What are the different heights of toilets?

    A measurement of 12 inches is standard, but 10-in. and 14-in. models are also available. “Comfort height” toilets, which sit about 17 to 19 inches high, or about two or three inches higher than usual have become the most common choice.

    How much space do you need in front of a toilet?

    Recommended: Plan a clear floor space of at least 30 inches from the front edge of all fixtures (lavatory, toilet, bidet, tub, and shower) to any opposite bath fixture, wall, or obstacle. Code Requirement: A minimum space of 21 inches must be planned in front of lavatory, toilet, bidet, and tub.

    What is the height of a comfort height toilet?

    Toilet height is measured from the floor to the top of the seat. Heights vary enough to be noticeable. Most often, they fall somewhere between 15” and 19”, with standard toilets coming in under 17”. However, chair height toilets, what Kohler refers to as Comfort Height® toilets, measure 17” or more.

    What is the rough in for toilets?

    Toilet rough in measuring: from wall to bolt cap. When talking toilets, the toilet rough in is the distance from the wall behind the toilet to the center of the outlet pipe where the waste leaves the toilet. Before replacing a toilet, measure the rough in or make sure your plumber measures before buying.

    What is the standard height of a toilet seat?

    The newest and most popular comfort height is typically around 16 1/8” floor to rim. The standard ADA (Americans with Disabilities Act) height toilets must have, a 17”-19” floor to bowl rim height, including the seat. You should also consider the toilet rough-in from the wall, which is commonly 12”.

    What is the rough in for a toilet?

    Toilet Rough-In Measurements and Standards. Make sure the new toilet will fit your space. To do this, measure the rough-in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor.

    How long is a roll of toilet paper?

    The average measures of a modern roll of toilet paper is c. 10 cm (31516 in.) wide, and 12 cm (42332 in.) in diameter, and weighs about 227 grams (8 oz.). An alternative method of packing the sheets uses interleaved sheets in boxes, or in bulk for use in dispensers.

    What is gpf toilet?

    Toilet water use can vary significantly. Older toilets can use 3.5, 5, or even up to 7 gallons of water with every flush. Federal plumbing standards now specify that new toilets can only use up to 1.6 gallons per flush (GPF), and there are high efficiency toilets that use up to 1.28 GPF.

    Who are Glacier Bay toilets made by?

    Chris Deziel. The company that manufactures Glacier Bay toilet products, North American conglomerate Foremost Groups, doesn’t sell these products directly. It distributes them exclusively through Home Depot, which is where you should go if you need a brand-name replacement part for your Glacier Bay toilet.

    How big is a bathroom sink?

    There is no standard size for a bath sink. Some petite basins are just big enough for washing hands, while the largest sinks are big enough for washing hair or delicate clothing. Most round sinks are 16 to 20 inches in diameter, while most rectangular sinks are 19 to 24 inches wide and 16 to 23 inches front to back.

    How big is a sink?

    Average cabinets measure 24 inches deep, 36 to 42 inches high and 25-1/4 to 26 inches wide.The standard 22-by-33 inch sink fits well within these dimensions. If your base cabinets are larger than this standard size, you may be able to accommodate a larger sink.